Ozone Generator Model Specification
Ozone generator model specifications, air purifiers, corona discharge ozonator water system, spa pool applications.
Ozone Air Purifiers
PZ6 Air Purifier Specifications: Size: 6 Wide x 6 x 1½ inches. Weight: less than 2 pounds. Silent, low cost operation (less than 50-watt light bulb). No filters or plates to clean or replace! Minimal maintenance, vacuum or blow dust from fan vent as needed. Electrical 110/120VAC. Ozone purity: 100%, no nitrogen by-products. Lamp arc life: 20,000 hours. One year manufacturers defect warranty.
PZ6-C Corona Hybrid Ozonator With Compressor Specifications. Ozone Output: 4,000 mg/day or 166 mg/hr. Ozone Concentration at 1CFH: 600 PPM. Ozone Purity: 99.9% Hydroxyl Free, 100% Free of Nitrous Compounds. EMI Suppression and Transient Protected: Up to 2,000VAC. Case: High Impact Polymer. System Life: 20,000 hours (nominal). Operating Temperature: +25°F. to +140°F. Weight: 14 ounces. Size: 6 Wide x 6 x 2½ inches. Standard System: 110VAC, 60hz; .35 amps and Molded Spa Ozone Plug. Custom Features: Electrical: Universal Solid State Inverter Ballast: 110 to 240VAC, 50/60 hz. Connector: 3-Prong NEMA, Len Gordon, AMP, Molex, all J and J, 3-Wire Pigtail. Two year warranty on ozone lamp and one year on compressor.
AV-2500 Ozone Generator Specifications: Size; 12x10x6 inches. Weight; 9.5 lbs. Electrical; Voltage 110/220V. Power; 100W. Cooling; Air cooled. Feed gas; Air. Dielectric; Class 6 quartz. Ozone output; From 100 to 2500mg/h with variable control. Square footage maximum for below 0.05 parts per million, 137,000 cu/ft. Construction; Stainless steel enclosure.
Corona Discharge Pool Spa Ozonator
Mini Spa 200 water ozonator specifications.
AQ-500 Spa Ozonator Specifications: Size; 8x6x3.5 inches. Weight; 4.5 lbs. Injector; The new design ensures maximum transfer of gas into the water. Electrical; 110/220 Volt. Power; 30W 60Hz with short circuit and flooded dielectric protection. Capacity; Up to 10,000 gallons with use of bromide (smaller dosages), 15,000 with chlorine or 1,000 to 3,000 gallon spa. Cooling; Air cooled. Feed gas requirements; Air Percentage: Ambient. Gas flow requirement; 10 L/M. Pressure: Negative. Dielectric; Corona Discharge Class 6 Quartz utilizing micro-gap technology. Spa Ozonator Warranty; 1 year on defects. Output; 500mg/h. Construction; White plastic enclosure. All wetted parts ozone resistant.
AQ-2000 Ozone Generator Specifications: Size Weight; 11x9.5x6 inches. 8 lbs. Injector; Design to ensure maximum transfer of gas into the water. Optional. Flow; required 15m3/h minimum. Electrical; Voltage 110/220 Volt. Power; 180 Watt with short circuit protection and flooded dielectric protection. Capacity; gallons depends on the pump cycles and if you use chlorine or bromide. Larger volumes can be done if more bromine is added. Cooling; Air cooled. Gas; Feed gas requirements, 12 Liter/Min Air, Pressure 1 bar abs. Dielectric; Single Corona Discharge Class 6 Quartz proprietary micro-gap technology. Warranty; 1 year on defects. Output; 2g/h from air, tested using humid air with 60 percent moisture. Dependent on the correct injector and air flow being maintained. Construction; Stainless steel water resistant enclosure. All wetted parts ozone resistant.
AQ-2KP and AQ-4KP Ozone Generator Specifications: Size; 10.2x5.9x5.5 inches or 260Lx150Wx140H. Weight: 6 - 7.23 lbs. Air cooled. Flow; required; 15Lpm minimum. Electrical; Voltage 110/220 Volt. Power; 220 Watt.
AQ-4000 Ozone Generator Specifications: Size Weight; 11x9.5x6 inches. 8.5 lbs. Injector; Design to ensure maximum transfer of gas into the water. Optional. Flow; required; 15m3/h minimum. Electrical; Voltage 110/220 Volt. Power; 180 Watts with short circuit protection and flooded dielectric protection. Capacity; gallons depends on the pump cycles and if you use chlorine or bromide. Larger volumes can be done if more bromine is added. Cooling; Air cooled. Gas; Feed gas requirements, 15 L/M Air, Pressure 1 bar. Dielectric; Two Corona Discharge Class 6 Quartz proprietary micro-gap technology. Warranty; 1 year on defects. Approx. Output; 4g/h from air, tested using humid air with 60 percent moisture. Dependent on the correct injector and air flow being maintained. Construction; Stainless steel water resistant enclosure. All wetted parts ozone resistant.
AQ-6000 and AQ-8000 Ozone Generator Specifications: Size Weight; 20.4x12.6x6.3 inches or 520Lx320Hx160D 8.5 lbs. 20 and 25 L/M air flow required.
M10G Specifications: Size Weight; 15x9.4x7.1 inches. 12 lbs. Injector; Design to ensure maximum transfer of gas into the water. Optional. Flow required; 15 m3/h minimum. Electrical; Voltage 110/220 Volt. Power; 180 Watt with short circuit protection and flooded dielectric protection. Capacity; gallons depends on the pump cycles. Larger volumes can be done if more bromide is added. Cooling; Air cooled. Gas; Feed gas requirements, Oxygen 7 Liter/Min. Percentage greater than 90 percent, Pressure 0.3 bar abs. Dielectric; Corona Discharge Class 6 Quartz proprietary micro-gap technology. Warranty; 1 Year on defects. Output; 10g/h from oxygen and 1.8g/h from air, tested using humid air with 60 percent moisture. Dependent on the correct injector and air flow being maintained. Construction; Stainless steel enclosure. All wetted parts ozone resistant.
M20G Specifications: Size Weight; 14.9x15.7x7 inches. 12.5 lbs. Injector; Design to ensure maximum transfer of gas into the water. Optional. Flow required; 15m3/h minimum. Electrical; Voltage 110/220 Volt. Power; 360 Watt with short circuit protection and flooded dielectric protection. Capacity; gallons depends on the pump cycles. Larger volumes can be done if more bromine is added. Cooling; Air cooled. Gas; Feed gas requirements, Oxygen 14 L/M Percentage greater than 90 percent, Pressure 0.3 bar abs. Dielectric; Corona Discharge Class 6 Quartz proprietary micro-gap technology. Warranty; 1 Year on defects. Output; 20g/h from oxygen and 3.6g/h from air, tested using humid air with 60 percent moisture. Dependent on the correct injector and air flow being maintained. Construction; Stainless steel enclosure. All wetted parts ozone resistant.
Injector Specifications: Size; 4.7x2.5 inches. Weight; 8 oz. approximately. Design; Proprietary design to ensure maximum transfer of gas into the water for spa or pool. Pipe Size; 1 1/2 inch glue on Plastic. Flow required; 530 ft3/h minimum. Construction; Ozone resistant materials.
Go to the following to figure the model for your size pool application.
Pool Ozone Generator Size Chart
Medical Ozone Generators
New AOS-1M Specifications: Size; 9.5 x 6.5 x 5 inches. Weight; 4 1/2 lbs. Electrical; 120 Volt. Power; 24 Watts 50/60Hz. Cooling; Air cooled 9 watt 25cfm fan. Feed gas requirements; O2. Dielectric; Pressurized Corona Discharge Stainless Cell and Quartz glass with variable control. Warranty; 1 year on manufacture defects and 3 years on power module. Output: 8-40 gamma at 1/2 liter/min. flow on oxygen. Construction; All wetted parts o3 resistant with 3/16 hose barb fittings.
Ozone Output Calibration Chart
NEW! AOS-1MD Specifications: Size; 10x8x8 inches. Weight; 9.5 lbs. Electrical; Voltage 110 Volt 60hz. Power; 60 Watt with short circuit protection. Cooling; Air cooled 9 watt 50cfm fan. Gas; Feed gas requirements greater than 90 percent O2. Dielectric; Pressurized Corona Discharge Stainless Reactor Cell. Warranty; 1 year on manufacture defects and 3 years on power module. Output; Variable output, 50+ gamma at 1/2 l/min. / Construction; Stainless steel enclosure. All wetted parts o3 resistant with hose barb fittings.
Front control panel includes 5 to 100 percent variable control with six-position range selector switch that allows for hundreds of different output settings.
AOS-1MD uses ozone resistant fittings and Silicone tubing, which comes in contact with ozone. The AOS-1MD is ideal for any medical application that requires dependable and stable ozone production. Built to last for years without any maintenance.
AOS-1MD Ozone Calibration Chart
AOS-1MS Specifications: Size; 11x7x5.5 inches. Weight; 5.5 lbs. Electrical; 110 or 220 Volt. Power; 40 W/60Hz with short circuit and flooded dielectric protection. Cooling; Air cooled. Feed gas requirements; O2. Dielectric; Pressurized Corona Discharge Stainless Cell with Class 6 Quartz utilizing micro-gap technology with variable control or four position switch. Warranty; 1 year on manufacture defects. Construction; All wetted parts o3 resistant with 3/16 hose barb fittings. Output: 50 gamma plus at 1/2 liter flow with fan. Model without fan is for light duty or intermittent use.
AOS-1MP Portable Home Air and Water Purifier Specifications and Features:
Size: 9.5x6.5x5 inches. Fused short circuit protection. External mini air compressor. Class 6 Quartz glass corona discharge dielectric tube with variable control. Voltage: Standard 110 Volts. Optional 220 Volt and 12 Volt. Air Compressor Flow Rate: 6.6scfh 3.1 liter/min @ .5psi. Complete with diffusion stone bubbler, hose and check valve. Warranty: Covers defects for one year from date of purchase. Meets or Exceeds UL/NSF Standards. LED light indicator shows power is ON. Output: 500mg/h @ 3.5 l/m air flow. Weight: 5.5 lbs.